Friday, October 19, 2012

How to make an EMP

You are sitting on your laptop reading the news. Suddenly, your laptop goes blank and the power shuts off. You attempt to turn it on but to no avail. You turn on your cell phone to find that the memory has been wiped. Nothing works, and you have no idea what is happening.

An EMP weapon could make that nightmare a reality.

EMPs (Electromagnetic Pulse) are released with Atomic Weapons. A nuclear weapon detonated high in the atmosphere could cause a widespread devastating EMP. Scientist are also researching a weapon that would provide only the electronic slaughtering power, minus the gamma rays.

But what better way to understand this technology than to make one yourself?

DISCLAIMER: This project is for entertainment purposes only. I am not responsible for any damage caused to Electronics by this device.

Ready to make an EMP?

I have two methods for you.

Method #1, Handheld

Handheld EMP?! I thought they only came in massive bomb types?

If you knew anything about EMPs before reading this, that's what you will think. Well, it is possible.

Amazingly, you don't even have to build a complex circuit. The entire circuit part of this project is already provided, pre-built. It costs around $5. Yes, the disposable camera strikes again!


To start your EMP project, you need a homemade Taser. This can be easily built from that vicious little tourist device above me. Scroll down a bit to find my guide on how to make one. It should literally take around 5 minutes.

Familiarize yourself with all the parts on the Camera's circuit board.

Now, you will need a few other parts. Go buy some insulated copper wire (the thicker the wire, the more powerful the EMP) and an iron rod. You can also use a non-metal rod, but this will be less powerful.




Take the copper wire and wrap it around the rod, TIGHTLY. As tight as possible. Once you are finished there will be a wire sticking out on either end.

Take the Camera Circuit (Taser) and solder the ends of the wires to the Capacitor. Make sure it is shorted first and the battery is out, unless you want to end up like the criminals mentioned in the Taser guide.

Now, GET OUTSIDE. Go far out into your backyard. Ensure that you don't have ANYTHING electronic in your pockets. Ensure that you don't have ANYTHING electronic in your hands. Heck, ensure you don't have ANYTHING electronic in your underwear, just in case. A mistake, and you may permanently break whatever you forgot to put away.

If you are using a Pacemakers or life support device, go get a hammer and smash your EMP. NEVER USE IT. You'll kill yourself. Keep this well away from anyone who has any of these devices.

Lastly, NEVER use it to interfere with other people's electronics or broadcasts. If you destroy some guy's iPhone with your EMP, you can be arrested as easily as if you took a chainsaw and destroyed it that way.

But of course you want to make sure it works. Hence why I said get outside. You aren't going to leave this awesome device sitting there not knowing if it works, are you? Of course not.

We need a guinea pig. No, not an actual guinea pig. The EMP wouldn't even affect it. A theoretical guinea pig. And the little device we are going to punish for no real reason? Meet the $0.99 Office Depot Calculator.


Look at that. Just asking for it, isn't it?

Maybe not, but it's only a dollar and is electronic. Need I say more?

Take your victim (the calculator, what were you thinking?) and place it as close to the EMP as possible without touching it. Again, ensure that you are nowhere near anything else electronic. Your EMP should have a blast radius of a few feet.

Put the battery in. Push the switch. If needed, you may want to remove the wires to charge the capacitor, but this as dangerous as you may shock yourself.

And...




No. None of that will happen. If you did everything right, you really shouldn't see anything. Once it is finished, go unplug the battery. Now, the moment of truth!

Pick up your (hopefully) dead victim and press the ON button. Does it work?

If yes, well, you did something wrong.

If no, CONGRATULATIONS! Your EMP is finished. Please keep reading for the warning at the end.

Method #2, EMP Explosive Device

This one is not re-usable. You also don't need a Camera.

First, check your local laws to find out if Firecrackers are legal. They are? Excellent!


Go to the Firecracker store and buy one.

Now, look up Neodymium Magnets. Neodymium is a Rare Earth that forms superb magnets. Buy two of them.



Make the EMP Coil rod as described in Method #1. But, instead of a solid rod, make sure that the rod is hollow and can fit the firecracker. Also, do not connect it to any Camera circuit or capacitor.

Stick the Neodymium magnets on either end of the firecracker, and connect the copper wires to the magnets. Put your electronic victim near the device (not too close or you will just blow it up). Make sure you are in a safe area with no people or electronics around. Take a match, light the fuse, and RUN! Get as far away as possible. The firecracker will explode and possibly send a neodymium magnet into your skull. However, it should generate the same EMP affect which will wipe out the Calculator.

Legal Issues. In the United States, do not use this device on any device other than your own or you risk being arrested. Keep it legal, and only break your own electronics.

Always keep the battery out when not using it, and store it away from electronics... just in case.

NEVER use this near ANYONE using a pacemaker or life support. Keep them as far away as possible, or you could hurt them.

If you have an RFID that needs killing, this works great!

Lastly, if you built an EMP Proof box and want to test it, just stick a calculator in there and fire off the EMP. If it still works, you did well.

Enjoy!

Questions? Use the comment function.

Enjoyed this Project? Tell your friends about MakeTech!

52 comments:

  1. You did not include how to make a taser out of the circuit. Can you please e-mail me the taser instuctions along with the EMP & a picture?

    Thank you for your time.

    Email: nanochip2000@gmail.com

    ReplyDelete
    Replies
    1. Sorry I found the taser instructions,but could you still send me a picture of the EMP? Also, the first EMP will likely destroy the device, right? If yes, is there a way to make a EMP that only disrupts electronics for an ammuont of time?

      Thanks again.

      Delete
    2. Hi. I am a big fan of your works. However, when I tried to make my EMP, nothing happens. so, I tried to remove the wires from the capacitor, then let it charge, and then touch the wires against the capacitor, thus making the current flow. The capacitor charges, like it should. Then, when I put the wires to it, it lets out a big spark. I don't know why this is happening. Please help.

      Delete
    3. Because when you charged the capacitor and connect it with the wires, you experienced a discharge. You probably build the EMP wrong so you should try to build it again

      Delete
  2. hi could u email me the full instructions of how to build emp device from a disposible camera please.. thanks.. rhauxwell@btinternet.com

    ReplyDelete
  3. Doesn't it need electricity or something? I mean the #1 project. I understand that I only need to connect the copper wires to the capacitor, without any batteries or such. Is that right?

    ReplyDelete
    Replies
    1. of course not. who needs electricity to charge a capacitor and run a freaking electrical circuit.

      Delete
    2. Bogdan, you put in the batteries that power the capacitor to power it

      Delete
    3. But if the camera is already charged, you don't need a battery. Just connect the wires to the capaciters

      Delete
    4. But if the camera is already charged, you don't need a battery. Just connect the wires to the capaciters

      Delete
  4. So what would the radius of the first method?

    ReplyDelete
    Replies
    1. I don't think it is effective beyond 3-4 feet....as maker did not made it directional, most of the MW energy is spread in all direction...you should use something like metal cone or satellite dish to concentrate this energy...FYI lens doesn't work here in this case

      Delete
    2. If you want a more deadly effect you should use a tactical flashlight. (taser)

      Delete
    3. Hi I am a big fan of your works. Can u tell me how to make an emp to knock out electronics within one foot distance with a stun gun taser ?

      Delete
  5. Does the rod have to be hollow like a tube? And Does the rod have to be iron? what about steel? Can you please answer back.

    ReplyDelete
    Replies
    1. Obviouslyhas to be hollow, you put the firecracker inside the rod to get effect.

      Delete
  6. hi could u email me the full instructions of how to build emp device from a disposible camera please.. thanks.. govender.nagesh@gmail.com

    ReplyDelete
  7. Could u email me the complete instructions for both of these? Thanks. ortasc@att.net

    ReplyDelete
  8. Can you email me a video on how to make a emp please

    My email is s10158111@gmail.com
    Thanks

    ReplyDelete
  9. Is there a way to make a EMP that only disrupts electronics for an ammuont of time?

    ReplyDelete
    Replies
    1. no as an electro magnetic pulse fries the electronic circuit. for that you would require a device known as a pinch, however they are difficult and expensive to make

      Delete
    2. actually there is a way. but the emp would have to be very week, like way weaker than this method, so weak that you only get a slight disruption on an old flip phone. just like what happen in Hawaii the day we dropped the bombs on japan. the emp was so weak that it only turned off a few street lights for about 15 minutes (now-a-days it would have probably messed up you phone since its still a strong emp when it comes to small electronics like a phone)

      Delete
  10. Full instructions are here: http://www.youtube.com/watch?v=c0vZigwn09I

    ReplyDelete
  11. Seriously... if you guys don't understand the basic principles behind this project (or apparently that capacitors, for some reason, need electricity to work), you'll probably end up hurting yourself.

    ReplyDelete
  12. What would the freq of the emp be? I'm considering building a faraday cage with the correct mesh size according to the freq

    ReplyDelete
  13. hey i am big fan of your works i love to do crazy things however i was not able to manage neodymium magnets is there any alternative for it and kindly mail me all instruction of how to make emp gun sort of my mail is


    sood.bhavya@yahoo.in thank u

    ReplyDelete
  14. Hey really loved the idea but would like to know how it looks and also couldn't find the guide for the taser, could you please e-mail me a picture and thE guide- hridaykchhabria@gmail.com
    Thanks.

    ReplyDelete
  15. Can you please manufacture a fully manufactured professional wide-radius blast army EMP device, stick it between your buttocks along with an hitachi vibrator, then go in the middle of a Mall and fire off the damn thing. You'd go sad because the vibrator would stop! ;)

    ReplyDelete
  16. If you solder a bigger capacitor in the other ones place it should multiply the effect right? But would the cameras charging circuit manage it?

    ReplyDelete
  17. i feel dumb asking this but whats keeping the copper wire to the rod?

    ReplyDelete
  18. So in theory if I up the size scale on the parts and use an aircraft battery I can make the emp spread out a little further?

    ReplyDelete
  19. I AM TIRED OF DISPOSABLE CAMERAS! Would you like to know what MY victim of choice is? A DISPOSABLE CAMERA! Is there any way at all I can build the circuit without one? Every single EMP generator I find runs on one.

    ReplyDelete
  20. can you email me the taser instuctions please?

    At: 02ikline@gmail.com

    Thanks

    ReplyDelete
  21. Is there any positive use of a small emp besides turning on a light bulb that isn't srewed into the socket?

    ReplyDelete
    Replies
    1. yes, it can be used to disable the morgellons living inside your body and fix health problems. an emp is the only way to disable them..
      im using an emp to fight my cancer. GOD Bless you

      Delete
  22. Hi super big fan of your work I was wondering can u send me the emp schamatic or the directions relley need help doing a science project

    ReplyDelete
  23. The reason all these instructions call for a camera is because the circuit that generates the required voltage is already built therein. Make your own generator and find your own capacitors. Also all of you idiots can stop asking for this to be emailed to you. The aurthor is not holding any secrets from you. Print what you read here.

    ReplyDelete
  24. can you send me full instructions. brodieclamp@gmail.com please dont spam

    ReplyDelete
  25. can you double up the copper coil to make the effect larger? or would it just interfere with itself?

    ReplyDelete
  26. please send circuit pic of emp bomb

    ReplyDelete
  27. please send circuit pic of emp bomb

    ReplyDelete
  28. I really loved your work but I wanted to the what does an employee really do to the victim. I mean does it destroy the capaciter of the circuit?

    ReplyDelete
  29. can we launch bullet /metal balls from emp
    please reply

    ReplyDelete
  30. can someone pls send me instructions for the taser thing and photos of the emp and steps @ yolomaster458@gmail.com

    ReplyDelete
  31. Nice blog… Thanks for sharing very useful information about electrical circuits.
    Learn Electronic Circuits

    ReplyDelete
  32. can some tell me how to build emp by designing our own circuit and not using built in components. please send it to my email anon53134@gmail.com

    ReplyDelete
  33. I have a generator out of a tatical flashlight (tazer) and the Kodak camera email me at shermanhubbard87@gmail.com what I can do to make a EMP that will cheat a pot o gold poker machines and give me extra credits or will make the game think I'm putting in more money

    ReplyDelete
  34. Can you send me them instructions please

    ReplyDelete
  35. How can I make a emp generator without camera out of componets the same or better than the circuit board in a camera. I noticed the camera circuit board could not take the capacitor bank I used nor the batteries I used it fried it quickly

    ReplyDelete

Translate

Total Pageviews

MakeTech Fans